93c5c50b9 Ensure that the serial device is enabled during part of OrientNormals test.
ff7db9780 Add RuntimeDeviceTracker::PrintSummary for debugging.
Acked-by: Kitware Robot <kwrobot@kitware.com>
Acked-by: Robert Maynard <robert.maynard@kitware.com>
Merge-request: !1810
This is a work around while we wait on requiring CMake 3.15 for all
cuda builds. At that point we can replace this with setting
`cuda_architecture_flags` as part of the EXPORT_PROPERTIES of the
vtkm_cuda target.
This has been tested with the ascent proxy
Once #377 is implemented we won't need this, but for now we have to
use the serial connectivity tables while validating the OrientNormals
output. Ensure that the serial device can be used during the validation
stage.
A non-const version of GetCoordinateSystem was added to implement a
change to the point transform filter. To make things symmetric (and
provide likely future needs), also add non-const versions of getting the
fields and cell sets.
The poly data and unstructured grid readers have to permute the cell
data to componsate for differences between VTK and VTK-m cell shapes.
Previously, this permutation was implemented by casting the read data to
a type and then changing the data. However, some code paths caused the
cast to fail. Get around that by doing the permutation in line when the
data are read.
Previously, the VTK file readers just skipped over everything in FIELD
sections. However, it is common for many point and cell fields to be
written in this section (it is how ParaView writes out most of its
data). This change will allow these fields to be read in correctly.
Previously, if a legacy VTK file had a METADATA section with an
INFORMATION subsection, the reader did not skip over it correctly.
Instead, it just read the rest of the file (and often encountered an
error). Change this to read and skip over the INFORMATION subsection
correctly.
The primary (likely only) use of PointTransform is to perform affine
transform on the position of the mesh. However, PointTransform did not
actually move the mesh. Rather, it just created a new field with the
transformed points.
Now, the output has its coordinate system replaced with the transformed
one generated (in addition to be added as a field). This can be turned
off (but defaults to on).
Also changed the constructor to turn on UseCoordinateSystemAsField so
that by default the filter operates on the existing coordinate system
and replaces it with the new coordinate system.
Also removed the template parameter on the filter. That added an
unnecessary complication to using it.
884616788 Simplify and extend AtomicArray implementation.
9560c4f63 Limit testing dispatch of atomic array to only atomic types.
0e728c800 Update atomic interfaces to support Add/CAS for UInt32/64.
720b452eb Force AtomicArray to use only basic storage arrays.
Acked-by: Kitware Robot <kwrobot@kitware.com>
Acked-by: Robert Maynard <robert.maynard@kitware.com>
Merge-request: !1802
- Use AtomicInterface to implement device-specific atomic operations.
- Remove DeviceAdapterAtomicArrayImplementations.
- Extend supported atomic types to include unsigned 32/64-bit ints.
- Add a static_assert to check that AtomicArray type is supported.
- Add documentation for AtomicArrayExecutionObject, including a CAS
example.
- Add a `T Get(idx)` method to AtomicArrayExecutionObject that does
an atomic load, and update existing CAS usage to use this instead
of `Add(idx, 0)`.
3eb91af96 Use ArrayGetValue where possible in worklets.
Acked-by: Kitware Robot <kwrobot@kitware.com>
Acked-by: Robert Maynard <robert.maynard@kitware.com>
Merge-request: !1799
Replace code such as `myArray.GetPortalControl().Get(0)` with
`vtkm::cont::ArrayGetValue(0, myArray)`, which will just retrieve
the single value without transferring the entire contents of
`myArray` to the host. This should prevent memory thrashing.
Also did some general style clean-ups and fixed loops that called
`GetPortalControl` in the loop body.
3a47058cb Use cache variables.
76ef9d15b Take advice of Robert and Kenneth on build system.
89fc012a2 Change CMakeLists.txt defaults in order to be more user-friendly.
Acked-by: Kitware Robot <kwrobot@kitware.com>
Acked-by: Kenneth Moreland <kmorel@sandia.gov>
Merge-request: !1771
709b12c5b Add checks for size of contour worklet outputs
a3131d4e1 Fix bad normals in contour test
Acked-by: Kitware Robot <kwrobot@kitware.com>
Acked-by: Li-Ta Lo <ollie@lanl.gov>
Merge-request: !1794
This allows for developers to do things such as the following
as constexpr's:
```cxx
constexpr vtkm::Id2 dims(16,16);
constexpr vtkm::Float64 dx = vtkm::Float64(4.0 * vtkm::Pi()) / vtkm::Float64(dims[0] - 1);
```