blender/doc/blender-scons.txt

$Id$

    Blenders SCons build scripts
    ============================

    Introduction
    ------------

    Since the beginning of 2004 Blender has had the SCons system as a
    build option. SCons is a Python-based, accurate build system. The
    scripts that were implemented in the first iteration worked, but
    the system grew quickly into such a state that maintaining it became
    a nightmare, and adding new features was just horrible, leading to
    many hacks without much sense in the overall structure.

    The rewrite has been waiting for a long time. Jonathan Jacobs provided
    a first overhaul of the scripts, which I used in the first phase of
    the rewrite. To make the system as maintainable as possible I made
    some radical changes, but thanks go to Jonathan for providing me
    with the patch to get started.

    This document describes the usage of the new SCons scripts. The
    inner workings are described in blender-scons-dev.txt.

    Building Blender
    ----------------

    To build Blender with the SCons scripts you need a full Python
    install, version 2.3 or later (http://www.python.org) and a SCons
    installation, version v0.96.1.D001 or later (http://www.scons.org).

    Check from the page
    http://www.blender.org/cms/Getting_Dependencies.135.0.html that you
    have all dependencies needed for building Blender. Note that for
    windows many of these dependencies already come in the lib/windows
    module from CVS.

    In the base directory of the sources (from now on called $BLENDERHOME)
    you'll see a file named SConstruct. This is the entry point for the
    SCons build system. In a terminal, change to this directory. To just
    build, issue the command 'scons':

        % scons

    This will start the build process with default values. Depending
    on your platform you may see colour in your output (non-Windows
    machines). In the the beginning an overview of targets and arguments
    from the command-line is given, then all libraries and binaries to
    build are configured.

    The build uses BF_BUILDDIR to build into and BF_INSTALLDIR to
    finally copy all needed files to get a proper setup. These
    variabbles have default values for every platform in
    $BLENDERHOME/config/(platform)-config.py. After the build successfully
    completes, you can find everything you need in BF_INSTALLDIR.


    Configuring the build
    ---------------------

    The default values for your platform can be found in the directory
    $BLENDERHOME/config. Your platform specific defaults are in
    (platform)-config.py, where platform is one of:

        - linux2, for machines running Linux
        - win32-vc, for Windows machines, compiling with a Microsoft compiler
        - win32-mingw, for Windows machines, compiling with the MingW compiler
        - darwin, for OS X machines
        (TBD: add cygwin, solaris and freebsd support)

    These files you will normally not change. If you need to override
    a default value, make a copy of the proper configuration to
    $BLENDERHOME/user-config.py. This file you can modify to your
    likings. Any value set here will override the ones from the
    (platform)-config.py.

    If you want to quickly test a new setting, you can give the option
    also on the command-line:

        % scons BF_BUILDDIR=../mybuilddir WITH_BF_OPENEXR=0

    This command sets the build directory to BF_BUILDDIR and disables
    OpenEXR support.

    If you need to know what can be set through the command-line, run
    scons with -h:

        % scons -h

    This command will print a long list with settable options and what
    every option means. Many of the default values will be empty, and
    from a fresh checkout without a user-config.py the actual values
    are the defaults as per $BLENDERHOME/config/(platform)-config.py
    (unless you have overridden any of them in your
    $BLENDERHOME/user-config.py).

    Configuring the output
    ----------------------

    This rewrite features a cleaner output during the build process. If
    you need to see the full command-line for compiles, then you can
    change that behaviour. Also the use of colours can be changed:

        % scons BF_FANCY=0

    This will disable the use of colours.

        % scons BF_QUIET=0

    This will give the old, noisy output. Every command-line per
    compile is printed out in its full glory. This is very useful when
    debugging problems with compiling, because you can see what the
    included paths are, what defines are given on the command-line,
    what compiler switches are used, etc.


    Supported toolset
    -----------------

    WINDOWS

        * msvc, this is a full install of Microsoft Visual C++. You'll
        likely have the .NET Framework SDK, Platform SDK and DX9 SDK
        installed * mstoolkit, this is the free MS VC++ 2003 Toolkit. You
        need to verify you have also the SDKs installed as mentioned
        for msvc.  * mingw, this is a minimal MingW install. TBD: write
        proper instructions on getting needed packages.

    On Windows with all of the three toolset installed you need to
    specify what toolset to use

        % scons BF_TOOLSET=msvc
        % scons BF_TOOLSET=mstoolkit
        % scons BF_TOOLSET=mingw

    If you have only the toolkit installed, you will also need to give
    BF_TOOLSET=mstoolkit on the command-line, to make sure everything is
    setup properly. Currently there is no good mechanism to automatically
    determine wether the found 'cl.exe' is from the toolkit or from a
    complete install.

    LINUX and OS X

    Currently only the default toolsets are supported for these platforms,
    so nothing special needs to be told to SCons when building. The
    defaults should work fine in most cases.

    Examples
    --------

    Build Blender with the defaults:

        % scons

    Build Blender, but disable OpenEXR support:

        % scons WITH_BF_OPENEXR=0

    Build Blender, enable debug symbols:

        % scons BF_DEBUG=1

    Build Blender, install to different directory:

        % scons BF_INSTALLDIR=/tmp/testbuild

    Build Blender in /tmp/obj and install to /usr/local:

        % scons BF_BUILDDIR=/tmp/obj BF_INSTALLDIR=/usr/local

    Clean BF_BUILDDIR:

        % scons clean

    Clean out the installed files:

        % scons -c

    /Nathan Letwory (jesterKing)