Separate getting a normal attribute and getting __dict__, was having to do too a check for __dict__ on each class (multiple times per getattro call from python) when its not used that often.
- Initialize python types with PyType_Ready, which adds methods to the type dictionary.
- use Pythons get/setattro (uses a python string for the attribute rather then char*). Using basic C strings seems nice but internally python converts them to python strings and discards them for most functions that accept char arrays.
- Method lookups use the PyTypes dictionary (should be faster then Py_FindMethod)
- Renamed __getattr -> py_base_getattro, _getattr -> py_getattro, __repr -> py_base_repr, py_delattro, py_getattro_self etc.
From here is possible to put all the parent classes methods into each python types dictionary to avoid nested lookups (api has 4 levels of lookups in some places), tested this but its not ready yet.
Simple tests for getting a method within a loop show this to be between 0.5 and 3.2x faster then using Py_FindMethod()
Use 'const char *' rather then the C++ 'STR_String' type for the attribute identifier of python attributes.
Each attribute and method access from python was allocating and freeing the string.
A simple test with getting an attribute a loop shows this speeds up attribute lookups a bit over 2x.
This patch introduces a simple state engine system with the logic bricks. This system features full
backward compatibility, multiple active states, multiple state transitions, automatic disabling of
sensor and actuators, full GUI support and selective display of sensors and actuators.
Note: Python API is available but not documented yet. It will be added asap.
State internals
===============
The state system is object based. The current state mask is stored in the object as a 32 bit value;
each bit set in the mask is an active state. The controllers have a state mask too but only one bit
can be set: a controller belongs to a single state. The game engine will only execute controllers
that belong to active states. Sensors and actuators don't have a state mask but are effectively
attached to states via their links to the controllers. Sensors and actuators can be connected to more
than one state. When a controller becomes inactive because of a state change, its links to sensors
and actuators are temporarily broken (until the state becomes active again). If an actuator gets isolated,
i.e all the links to controllers are broken, it is automatically disabled. If a sensor gets isolated,
the game engine will stop calling it to save CPU. It will also reset the sensor internal state so that
it can react as if the game just started when it gets reconnected to an active controller. For example,
an Always sensor in no pulse mode that is connected to a single state (i.e connected to one or more
controllers of a single state) will generate a pulse each time the state becomes active. This feature is
not available on all sensors, see the notes below.
GUI
===
This system system is fully configurable through the GUI: the object state mask is visible under the
object bar in the controller's colum as an array of buttons just like the 3D view layer mask.
Click on a state bit to only display the controllers of that state. You can select more than one state
with SHIFT-click. The All button sets all the bits so that you can see all the controllers of the object.
The Ini button sets the state mask back to the object default state. You can change the default state
of object by first selecting the desired state mask and storing using the menu under the State button.
If you define a default state mask, it will be loaded into the object state make when you load the blend
file or when you run the game under the blenderplayer. However, when you run the game under Blender,
the current selected state mask will be used as the startup state for the object. This allows you to test
specific state during the game design.
The controller display the state they belong to with a new button in the controller header. When you add
a new controller, it is added by default in the lowest enabled state. You can change the controller state
by clicking on the button and selecting another state. If more than one state is enabled in the object
state mask, controllers are grouped by state for more readibility.
The new Sta button in the sensor and actuator column header allows you to display only the sensors and
actuators that are linked to visible controllers.
A new state actuator is available to modify the state during the game. It defines a bit mask and
the operation to apply on the current object state mask:
Cpy: the bit mask is copied to the object state mask.
Add: the bits that set in the bit mask will be turned on in the object state mask.
Sub: the bits that set in the bit mask will be turned off in the object state mask.
Inv: the bits that set in the bit mask will be inverted in the objecyy state mask.
Notes
=====
- Although states have no name, a simply convention consists in using the name of the first controller
of the state as the state name. The GUI will support that convention by displaying as a hint the name
of the first controller of the state when you move the mouse over a state bit of the object state mask
or of the state actuator bit mask.
- Each object has a state mask and each object can have a state engine but if several objects are
part of a logical group, it is recommended to put the state engine only in the main object and to
link the controllers of that object to the sensors and actuators of the different objects.
- When loading an old blend file, the state mask of all objects and controllers are initialized to 1
so that all the controllers belong to this single state. This ensures backward compatibility with
existing game.
- When the state actuator is activated at the same time as other actuators, these actuators are
guaranteed to execute before being eventually disabled due to the state change. This is useful for
example to send a message or update a property at the time of changing the state.
- Sensors that depend on underlying resource won't reset fully when they are isolated. By the time they
are acticated again, they will behave as follow:
* keyboard sensor: keys already pressed won't be detected. The keyboard sensor is only sensitive
to new key press.
* collision sensor: objects already colliding won't be detected. Only new collisions are
detected.
* near and radar sensor: same as collision sensor.
(adding)
#ifdef HAVE_CONFIG_H
#include <config.h>
#endif
also the Makefile.in's were from previous patch adding
the system depend stuff to configure.ac
Kent
--
mein@cs.umn.edu
