This patch separates setting of hardware interfaec and software
interface MTU. Software MTU is L2 payload MTU (i.e. not including L2
header). Per-protocol MTU for IPv4, IPv6 and MPLS can also be set.
Currently only IP4, IP6 are enabled in adjacency / rewrite code.
Documentation in src/vnet/MTU.md
Change-Id: Iee2fd6f0bbc8210748dd8e073ab9fab87d323690
Signed-off-by: Ole Troan <ot@cisco.com>
This reverts commit 70083ee74c.
Reverting as this patch is causing following crash:
0: /home/damarion/cisco/vpp3/build-data/../src/vnet/devices/devices.h:131 (vnet_get_device_input_thread_index) assertion `queue_id < vec_len (hw->input_node_thread_index_by_queue)' fails
Aborted
Change-Id: Ie2a365032110b1f67be7a9d832885b9899813d39
Signed-off-by: Damjan Marion <damarion@cisco.com>
- setting MTU on an interface updates the L3 max bytes too
- value cached in the adjacency is also updated
- MTU exceeded generates ICMP to sender
Change-Id: I343ec71d8e903b529594c4bd0543f04bc7f370b3
Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
- new IPv4 and IPv6 feature arcs on the punt and drop nodes
- new features:
- redirect punted traffic to an interface and nexthop
- police punted traffic.
Change-Id: I53be8bf4e06545add8a3619e462de5ffedd0a95c
Signed-off-by: Neale Ranns <nranns@cisco.com>
part 2;
- this adds the code to create an IP and MPLS table via the API.
- but the enforcement that the table must be created before it is used is still missing, this is so that CSIT can pass.
Change-Id: Id124d884ade6cb7da947225200e3bb193454c555
Signed-off-by: Neale Ranns <nranns@cisco.com>
- the flow hash config is (and was) cached on the load-balance object so the fib_table_t struct is not used a switch time. Therefore changes to the table's flow hash config need to be propagated to all load-balances and hance all FIB entries in the table.
- enable API for setting the IPv6 table flow hash config
- use only the hash config in the fib_table_t object and not on the ipX_fib_t
- add tests.
Change-Id: Ib804c11162c6d4972c764957562c372f663e05d4
Signed-off-by: Neale Ranns <nranns@cisco.com>
Drop comes before lookup when enabled. is_first_or_last is not required when setting a feature, the anchor is added in find_config_with_features().
Don't make the PG interfaces automatically L3 enabled, this way we can have tests that check the L3 protocol disbaled behaviour.
Change-Id: Icef22a920b27ff9cec6ab2da6b05f05c532cb60f
Signed-off-by: Neale Ranns <nranns@cisco.com>
Perform accounting of expected packets based on created packet infos.
Use this accounting info to automatically expect (and verify) the
correct number of packets to be captured. Automatically retry the read
of the capture file if scapy raises an exception while doing so to
handle rare cases when capture file is read while only partially
written during busy wait. Don't fail assert_nothing_captured if only
junk packets arrived.
Change-Id: I16ec2e9410ef510d313ec16b7e13c57d0b2a63f5
Signed-off-by: Klement Sekera <ksekera@cisco.com>
