* Rename `eeprom_stm32` to `eeprom_legacy_emulated_flash`.
* Rename `flash_stm32` to `legacy_flash_ops`.
* Rename `eeprom_teensy` to `eeprom_kinetis_flexram`.
* Move Bluetooth-related function calls up to host/keyboard level
* Remove pointless set_output() call
* Move bluetooth (rn42) init to end of keyboard_init()
* Enable SPI/UART for ChibiOS targets
* Some more slight tweaks
* [Core] Rework PS/2 driver selection
Enabling and selecting PS/2 driver was using old approach,
so it was reworked to current approach, inspired by Serial
and WS2812 driver selections.
* [Keyboard] Update keyboards using PS/2 to use new PS/2 driver selection
* [Docs] Update PS/2 documentation to use new PS/2 driver selection
* Fix indentation
* [Core] Add PS2 to data driver
* Fix oversight in property name
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Add PS/2 pins to data driven mappings
Co-authored-by: Drashna Jaelre <drashna@live.com>
* PMW33XX drivers overhaul
This combines the PMW3389 and PM3360 drivers as they only differ in the
firmware blobs and CPI get and set functions. The following changes have
been made:
* PMW3389 now gets the same multi-sensor feature that is already available on the
PMW3360.
* Introduced a shared pmw33xx_report_t struct is now directly readable via SPI
transactions instead of individual byte-sized reads, saving multiple
copies and bitshift operations.
* pmw33(89/60)_get_report functions had unreachable branches in their motion
detection logic these have been simplied as much as possible.
* The fast firmware upload option has been removed as this becomes obsolete by
the newly introduced polled waiting functions for ChibiOS polled waiting
* PMW33(60/89)_SPI_LSBFIRST and PMW33(60/89)_SPI_MODE config options
have been removed as they don't need to be configurable.
* All PMW3389 and PMW3360 defines have been unified to a PMW33XX prefix
to reduce code duplication and make the defines interchangeable
* Adjust keyboards to PMW33XX naming scheme
mpaland printf implementation was abandoned in ~2019 and the fork by
eyalroz is now regarded to be the goto replacement of it. So this commit
incoporates the changes needed to use this fork in QMK.
Note that pointer ptrdiff_t is always supported since commit
51c90f93a97fdaef895783ecbe24569be0db7cb8
* Tentative Teensy 3.5 support
* Set firmware format to .hex for ARM Teensys
* Got to "device descriptor failed" by comparing with Teensy 3.6 code
* Drop down to 96MHz...
* Bump back up to 120MHz
* Disable RESET keycode because of naming conflicts
* Add Pico SDK as submodule
* Add RP2040 build support to QMK
* Adjust USB endpoint structs for RP2040
* Add RP2040 bootloader and double-tap reset routine
* Add generic and pro micro RP2040 boards
* Add RP2040 onekey keyboard
* Add WS2812 PIO DMA enabled driver and documentation
Supports regular and open-drain output configuration. RP2040 GPIOs are
sadly not 5V tolerant, so this is a bit use-less or needs extra hardware
or you take the risk to fry your hardware.
* Adjust SIO Driver for RP2040
* Adjust I2C Driver for RP2040
* Adjust SPI Driver for RP2040
* Add PIO serial driver and documentation
* Add general RP2040 documentation
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Initial import of wear-leveling algorithm.
* Alignment.
* Docs tweaks.
* Lock/unlock.
* Update quantum/wear_leveling/wear_leveling_internal.h
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* More tests, fix issue with consolidation when unlocked.
* More tests.
* Review comments.
* Add plumbing for FNV1a.
* Another test checking that checksum mismatch clears the cache.
* Check that the write log still gets played back.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Refactor steno into STENO_ENABLE_[ALL|GEMINI|BOLT]
* Update stenography documentation
* STENO_ENABLE_TXBOLT → STENO_ENABLE_BOLT
TXBOLT is a better name but BOLT is more consistent with the
pre-existing TX Bolt related constants, which all drop the "TX " prefix
* Comments
* STENO_ENABLE_[GEMINI|BOLT|ALL] → STENO_PROTOCOL = [geminipr|txbolt|all]
* Add note on lacking V-USB support
* Clear chord at the end of the switch(mode){send_steno_chord} block
* Return true if NOEVENT
* update_chord_xxx → add_xxx_key_to_chord
* Enable the defines for all the protocols if STENO_PROTOCOL = all
* Mention how to use `steno_set_mode`
* Set the default steno protocol to "all"
This is done so that existing keymaps invoking `steno_set_mode` don't
all suddenly break
* Add data driver equivalents for stenography feature
* Document format of serial steno packets
(Thanks dnaq)
* Add missing comma
