Initial unorthodox support

Keymap: Finex Redox keymap (#4418 )
* Added FiNeX custom Redox Layout, first commit. * updated readme * removed old code
2018-11-14 08:46:58 -08:00 · 2018-11-13 14:44:50 -08:00 · 2018-11-13 14:20:42 -08:00 · 2018-11-13 12:27:33 -08:00 · 2018-11-13 08:38:48 -08:00 · 2018-11-13 08:31:25 -08:00
89 changed files with 7055 additions and 672 deletions
--- a/docs/features.md
+++ b/docs/features.md
@@ -8,7 +8,7 @@ QMK has a staggering number of features for building your keyboard. It can take
 * [Auto Shift](feature_auto_shift.md) - Tap for the normal key, hold slightly longer for its shifted state.
 * [Backlight](feature_backlight.md) - LED lighting support for your keyboard.
 * [Bootmagic](feature_bootmagic.md) - Adjust the behavior of your keyboard using hotkeys.
-* [Combos](feature_combos.md) - Custom actions for multiple key holds.
+* [Combos](feature_combo.md) - Custom actions for multiple key holds.
 * [Command](feature_command.md) - Runtime version of bootmagic (Formerly known as "Magic").
 * [Dynamic Macros](feature_dynamic_macros.md) - Record and playback macros from the keyboard itself.
 * [Grave Escape](feature_grave_esc.md) - Lets you use a single key for Esc and Grave. 
--- a/docs/i2c_driver.md
+++ b/docs/i2c_driver.md
@@ -8,7 +8,6 @@ The I2C Master drivers used in QMK have a set of common functions to allow porta
 |------------------------------------------------------------------------------------------------------------------|-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------|
 |`void i2c_init(void);`                                                                                            |Initializes the I2C driver. This function should be called once before any transaction is initiated.                                                                         |
 |`uint8_t i2c_start(uint8_t address);`                                                                             |Starts an I2C transaction. Address is the 7-bit slave address without the direction bit.                                                                                     |
-|`uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);`                        |Transmit data over I2C. Address is the 7-bit slave address without the direction.                                                                                            |
 |`uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);`                        |Transmit data over I2C. Address is the 7-bit slave address without the direction. Returns status of transaction.                                                             |
 |`uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);`                         |Receive data over I2C. Address is the 7-bit slave address without the direction. Saves number of bytes specified by `length` in `data` array. Returns status of transaction. |
 |`uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);`       |Same as the `i2c_transmit` function but `regaddr` sets where in the slave the data will be written.                                                                          |
--- a/docs/keycodes.md
+++ b/docs/keycodes.md
@@ -141,9 +141,9 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_LOCKING_SCROLL`    |`KC_LSCR`           |Locking Scroll Lock                            |
 |`KC_KP_COMMA`          |`KC_PCMM`           |Keypad `,`                                     |
 |`KC_KP_EQUAL_AS400`    |                    |Keypad `=` on AS/400 keyboards                 |
-|`KC_INT1`              |`KC_RO`             |JIS `\` and <code>&#124;</code>                |
+|`KC_INT1`              |`KC_RO`             |JIS `\` and `_`                                |
 |`KC_INT2`              |`KC_KANA`           |JIS Katakana/Hiragana                          |
-|`KC_INT3`              |`KC_JYEN`           |JIS `¥`                                        |
+|`KC_INT3`              |`KC_JYEN`           |JIS `¥` and <code>&#124;</code>                |
 |`KC_INT4`              |`KC_HENK`           |JIS Henkan                                     |
 |`KC_INT5`              |`KC_MHEN`           |JIS Muhenkan                                   |
 |`KC_INT6`              |                    |JIS Numpad `,`                                 |
--- a/docs/keycodes_basic.md
+++ b/docs/keycodes_basic.md
@@ -123,9 +123,9 @@ The basic set of keycodes are based on the [HID Keyboard/Keypad Usage Page (0x07

 |Key       |Aliases  |Description                    |
 |----------|---------|-------------------------------|
-|`KC_INT1` |`KC_RO`  |JIS `\` and <code>&#124;</code>|
+|`KC_INT1` |`KC_RO`  |JIS `\` and `_`                |
 |`KC_INT2` |`KC_KANA`|JIS Katakana/Hiragana          |
-|`KC_INT3` |`KC_JYEN`|JIS `¥`                        |
+|`KC_INT3` |`KC_JYEN`|JIS `¥` and <code>&#124;</code>|
 |`KC_INT4` |`KC_HENK`|JIS Henkan                     |
 |`KC_INT5` |`KC_MHEN`|JIS Muhenkan                   |
 |`KC_INT6` |         |JIS Numpad `,`                 |
--- a/keyboards/412_64/412_64.c
+++ b/keyboards/412_64/412_64.c
@@ -0,0 +1,29 @@
+
+#include "412_64.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}
--- a/keyboards/412_64/412_64.h
+++ b/keyboards/412_64/412_64.h
@@ -0,0 +1,29 @@
+
+#ifndef FOURx16_H
+#define FOURx16_H
+
+#include "quantum.h"
+#define ___ KC_NO
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+
+#define LAYOUT_ortho_4x16( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, K13, K14, K15, \
+    K16, K17, K18, K19, K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K30, K31, \
+    K32, K33, K34, K35, K36, K37, K38, K39, K40, K41, K42, K43, K44, K45, K46, K47, \
+    K48, K49, K50, K51, K52, K53, K54, K55, K56, K57, K58, K59, K60, K61, K62, K63 \
+) \
+{ \
+    { K00, K02, K04, K06, K08, K10, K12, K14 }, \
+    { K01, K03, K05, K07, K09, K11, K13, K15 }, \
+    { K16, K18, K20, K22, K24, K26, K28, K30 }, \
+    { K17, K19, K21, K23, K25, K27, K29, K31 }, \
+    { K32, K34, K36, K38, K40, K42, K44, K46 }, \
+    { K33, K35, K37, K39, K41, K43, K45, K47 }, \
+    { K48, K50, K52, K54, K56, K58, K60, K62 }, \
+    { K49, K51, K53, K55, K57, K59, K61, K63 } \
+}
+
+#endif
--- a/keyboards/412_64/config.h
+++ b/keyboards/412_64/config.h
@@ -0,0 +1,202 @@
+
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xF7E0
+#define PRODUCT_ID      0x0412
+#define DEVICE_VER      0x0000
+#define MANUFACTURER    EDI/SCI
+#define PRODUCT         412 64 Model 00
+#define DESCRIPTION     A compact 60% keyboard inspired by the 4x4x4x4x4
+
+/* key matrix size */
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 8
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D3, F4, F5, F6, F7, B1, B3, B2 }
+#define MATRIX_COL_PINS { B0, D2, D0, D1, D4, C6, D7, E6 }
+#define UNUSED_PINS { B4, B5, B6, B7, C7, F0, F1 }
+
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN C7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
--- a/keyboards/412_64/keymaps/default/config.h
+++ b/keyboards/412_64/keymaps/default/config.h
@@ -0,0 +1,5 @@
+
+
+#pragma once
+
+// place overrides here
--- a/keyboards/412_64/keymaps/default/keymap.c
+++ b/keyboards/412_64/keymaps/default/keymap.c
@@ -0,0 +1,105 @@
+
+#include QMK_KEYBOARD_H
+
+#define _MAIN 0
+#define _RAISE 1
+#define _LOWER 2
+
+// Readability keycodes
+#define LOWER   MO(_LOWER)
+#define RAISE   MO(_RAISE)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+
+/* MAIN
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------.
+ * | TAB    | Q      | W      | E      | R      | T      | Y      | U      | I      | O      | P      | Backsp | Delete |   7    |   8    |   9    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | ESC    | A      | S      | D      | F      | G      | H      | J      | K      | L      | ;      | '      |  PgUp  |   4    |   5    |   6    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | SHIFT  | Z      | X      | C      | V      | B      | N      | M      | ,      | .      | /      | ENTER  |  PgDn  |   1    |   2    |   3    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | LCTRL  |  PAUS  | GUI    | ALT    | Lower  | Space  |  Space | Raise  | Left   | Down   | Up     | Right  |  Shift |   0    |   .    |  ENTER |
+ * '-----------------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
+  [_MAIN] = LAYOUT_ortho_4x16(
+  KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC, KC_DEL, KC_KP_7, KC_KP_8, KC_KP_9,
+  KC_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_PGUP, KC_KP_4, KC_KP_5, KC_KP_6,
+  KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_ENT,  KC_PGDN, KC_KP_1, KC_KP_2, KC_KP_3,
+  KC_LCTL, KC_PAUS, KC_LGUI, KC_LALT, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_RSFT, KC_KP_0, KC_KP_DOT, KC_PENT
+  ),
+
+/* RAISE
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------.
+ * |    `   |  1     |  2     |  3     |  4     |  5     |  6     |  7     |  8     |  9     |  0     |        | Insert |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        |        |        |        |        |        |        | -      | =      | [      | ]      |   \    |  Home  |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        |        |        |        |        |        |        |  ISO # |  ISO / |        |        |  PScr  |  End   |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        |        |        |        |        |                 |        |  Next  |  Vol-  |  Vol+  |  Play  |        |        |        |        |
+ * '-----------------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
+  [_RAISE] = LAYOUT_ortho_4x16(
+  KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    _______, KC_INS, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS, KC_HOME, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, KC_NUHS, KC_NUBS, _______, _______, KC_PSCR, KC_END, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY, _______, _______, _______, _______
+  ),
+
+/* LOWER
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------.
+ * |    ~   |    !   |    @   |    #   |    $   |    %   |    ^   |    &   |    *   |    (   |    )   |        |        |        |        | Reset  |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        |   F1   |   F2   |   F3   |   F4   |   F5   |   F6   |    _   |    +   |    {   |    }   |   |    |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        |   F7   |   F8   |   F9   |  F10   |  F11   |  F12   | ISO ~  | ISO |  |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        |        |        |        |        |                 |        |        |        |        |  Mute  |        |        |        |        |
+ * '-----------------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
+  [_LOWER] = LAYOUT_ortho_4x16(
+  KC_TILD, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______,  _______, _______, _______, RESET,
+  _______,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_UNDS, KC_PLUS,  KC_LCBR, KC_RCBR, KC_PIPE, _______, _______, _______, _______,
+  _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,S(KC_NUHS),S(KC_NUBS), _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, _______, _______, _______, _______
+  ),
+
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  keyevent_t event = record->event;
+    (void)event;
+
+  switch (id) {
+
+  }
+  return MACRO_NONE;
+}
+
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}
--- a/keyboards/412_64/keymaps/default/rules.mk
+++ b/keyboards/412_64/keymaps/default/rules.mk
@@ -0,0 +1 @@
+KEY_LOCK_ENABLE = yes       # Enable the universal locking key, which lets you do any locking you require.
--- a/keyboards/412_64/readme.md
+++ b/keyboards/412_64/readme.md
@@ -0,0 +1,15 @@
+# 412-64
+
+![412-64](image_here)
+
+A compact 60% keyboard designed by Fate Everywhere and sold on a limited basis. Born out of the desire for a Planck with a numpad for technical work.
+
+Keyboard Maintainer: [Fate Everywhere](https://github.com/fateeverywhere)  
+Hardware Supported: 4x16 T&E Prototype, 412-64 Mk. 0, Mk. 1.  
+Hardware Availability: Highly limited, contact /u/FateEverywhere on reddit for availability.
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 412-64:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
--- a/keyboards/412_64/rules.mk
+++ b/keyboards/412_64/rules.mk
@@ -0,0 +1,73 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = atmel-dfu
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = ortho_4x16 
--- a/keyboards/clueboard/unorthodox/boards/GENERIC_STM32_F303XC/board.c
+++ b/keyboards/clueboard/unorthodox/boards/GENERIC_STM32_F303XC/board.c
@@ -0,0 +1,126 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#include "hal.h"
+
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+/**
+ * @brief   PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ *          This variable is used by the HAL when initializing the PAL driver.
+ */
+const PALConfig pal_default_config = {
+#if STM32_HAS_GPIOA
+  {VAL_GPIOA_MODER, VAL_GPIOA_OTYPER, VAL_GPIOA_OSPEEDR, VAL_GPIOA_PUPDR,
+   VAL_GPIOA_ODR,   VAL_GPIOA_AFRL,   VAL_GPIOA_AFRH},
+#endif
+#if STM32_HAS_GPIOB
+  {VAL_GPIOB_MODER, VAL_GPIOB_OTYPER, VAL_GPIOB_OSPEEDR, VAL_GPIOB_PUPDR,
+   VAL_GPIOB_ODR,   VAL_GPIOB_AFRL,   VAL_GPIOB_AFRH},
+#endif
+#if STM32_HAS_GPIOC
+  {VAL_GPIOC_MODER, VAL_GPIOC_OTYPER, VAL_GPIOC_OSPEEDR, VAL_GPIOC_PUPDR,
+   VAL_GPIOC_ODR,   VAL_GPIOC_AFRL,   VAL_GPIOC_AFRH},
+#endif
+#if STM32_HAS_GPIOD
+  {VAL_GPIOD_MODER, VAL_GPIOD_OTYPER, VAL_GPIOD_OSPEEDR, VAL_GPIOD_PUPDR,
+   VAL_GPIOD_ODR,   VAL_GPIOD_AFRL,   VAL_GPIOD_AFRH},
+#endif
+#if STM32_HAS_GPIOE
+  {VAL_GPIOE_MODER, VAL_GPIOE_OTYPER, VAL_GPIOE_OSPEEDR, VAL_GPIOE_PUPDR,
+   VAL_GPIOE_ODR,   VAL_GPIOE_AFRL,   VAL_GPIOE_AFRH},
+#endif
+#if STM32_HAS_GPIOF
+  {VAL_GPIOF_MODER, VAL_GPIOF_OTYPER, VAL_GPIOF_OSPEEDR, VAL_GPIOF_PUPDR,
+   VAL_GPIOF_ODR,   VAL_GPIOF_AFRL,   VAL_GPIOF_AFRH},
+#endif
+#if STM32_HAS_GPIOG
+  {VAL_GPIOG_MODER, VAL_GPIOG_OTYPER, VAL_GPIOG_OSPEEDR, VAL_GPIOG_PUPDR,
+   VAL_GPIOG_ODR,   VAL_GPIOG_AFRL,   VAL_GPIOG_AFRH},
+#endif
+#if STM32_HAS_GPIOH
+  {VAL_GPIOH_MODER, VAL_GPIOH_OTYPER, VAL_GPIOH_OSPEEDR, VAL_GPIOH_PUPDR,
+   VAL_GPIOH_ODR,   VAL_GPIOH_AFRL,   VAL_GPIOH_AFRH},
+#endif
+#if STM32_HAS_GPIOI
+  {VAL_GPIOI_MODER, VAL_GPIOI_OTYPER, VAL_GPIOI_OSPEEDR, VAL_GPIOI_PUPDR,
+   VAL_GPIOI_ODR,   VAL_GPIOI_AFRL,   VAL_GPIOI_AFRH}
+#endif
+};
+#endif
+
+void enter_bootloader_mode_if_requested(void);
+
+/**
+ * @brief   Early initialization code.
+ * @details This initialization must be performed just after stack setup
+ *          and before any other initialization.
+ */
+void __early_init(void) {
+  enter_bootloader_mode_if_requested();
+  stm32_clock_init();
+}
+
+#if HAL_USE_SDC || defined(__DOXYGEN__)
+/**
+ * @brief   SDC card detection.
+ */
+bool sdc_lld_is_card_inserted(SDCDriver *sdcp) {
+
+  (void)sdcp;
+  /* TODO: Fill the implementation.*/
+  return true;
+}
+
+/**
+ * @brief   SDC card write protection detection.
+ */
+bool sdc_lld_is_write_protected(SDCDriver *sdcp) {
+
+  (void)sdcp;
+  /* TODO: Fill the implementation.*/
+  return false;
+}
+#endif /* HAL_USE_SDC */
+
+#if HAL_USE_MMC_SPI || defined(__DOXYGEN__)
+/**
+ * @brief   MMC_SPI card detection.
+ */
+bool mmc_lld_is_card_inserted(MMCDriver *mmcp) {
+
+  (void)mmcp;
+  /* TODO: Fill the implementation.*/
+  return true;
+}
+
+/**
+ * @brief   MMC_SPI card write protection detection.
+ */
+bool mmc_lld_is_write_protected(MMCDriver *mmcp) {
+
+  (void)mmcp;
+  /* TODO: Fill the implementation.*/
+  return false;
+}
+#endif
+
+/**
+ * @brief   Board-specific initialization code.
+ * @todo    Add your board-specific code, if any.
+ */
+void boardInit(void) {
+}
--- a/keyboards/clueboard/unorthodox/boards/GENERIC_STM32_F303XC/board.h
+++ b/keyboards/clueboard/unorthodox/boards/GENERIC_STM32_F303XC/board.h
--- a/keyboards/clueboard/unorthodox/boards/GENERIC_STM32_F303XC/board.mk
+++ b/keyboards/clueboard/unorthodox/boards/GENERIC_STM32_F303XC/board.mk
@@ -0,0 +1,5 @@
+# List of all the board related files.
+BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F303XC/board.c
+
+# Required include directories
+BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F303XC
--- a/keyboards/clueboard/unorthodox/bootloader_defs.h
+++ b/keyboards/clueboard/unorthodox/bootloader_defs.h
@@ -0,0 +1,7 @@
+/* Address for jumping to bootloader on STM32 chips. */
+/* It is chip dependent, the correct number can be looked up here:
+ * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+ * This also requires a patch to chibios:
+ *  <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
+ */
+#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800
--- a/keyboards/clueboard/unorthodox/chconf.h
+++ b/keyboards/clueboard/unorthodox/chconf.h
--- a/keyboards/clueboard/unorthodox/config.h
+++ b/keyboards/clueboard/unorthodox/config.h
@@ -0,0 +1,121 @@
+/* Copyright 2018 Jack Humbert
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xC1ED
+#define PRODUCT_ID      0x23C0
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Clueboard
+#define PRODUCT         Unorthodox
+#define DESCRIPTION     A compact row-staggered keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 8
+
+#define MATRIX_ROW_PINS { B4, B3, B2, B1, B0 }
+#define MATRIX_COL_PINS { B5, A3, A2, A1, A0, B13, B14, B15 }
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 6
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+//#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+  keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+// #define WS2812_LED_N 2
+// #define RGBLED_NUM WS2812_LED_N
+// #define WS2812_TIM_N 2
+// #define WS2812_TIM_CH 2
+// #define PORT_WS2812     GPIOA
+// #define PIN_WS2812      1
+// #define WS2812_DMA_STREAM STM32_DMA1_STREAM2  // DMA stream for TIMx_UP (look up in reference manual under DMA Channel selection)
+//#define WS2812_DMA_CHANNEL 7                  // DMA channel for TIMx_UP
+//#define WS2812_EXTERNAL_PULLUP
+
--- a/keyboards/clueboard/unorthodox/halconf.h
+++ b/keyboards/clueboard/unorthodox/halconf.h
--- a/keyboards/clueboard/unorthodox/keymaps/default/keymap.c
+++ b/keyboards/clueboard/unorthodox/keymaps/default/keymap.c
@@ -1,4 +1,4 @@
-/* Copyright 2017 Jason Williams (Wilba)
+/* Copyright 2018 Zach White
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
@@ -13,27 +13,15 @@
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
-#pragma once

-#define PROTOCOL_VERSION 0x0001
+#include QMK_KEYBOARD_H

-enum m6_b_command_id
-{
-	id_get_protocol_version = 0x01, // always 0x01
-	id_get_keyboard_value,
-	id_set_keyboard_value,
-	id_dynamic_keymap_get_keycode,
-	id_dynamic_keymap_set_keycode,
-	id_dynamic_keymap_reset,
-	id_backlight_config_set_value,
-	id_backlight_config_get_value,
-	id_backlight_config_save,
-	id_eeprom_reset,
-	id_bootloader_jump,
-	id_unhandled = 0xFF,
-};
-
-enum m6_b_keyboard_value_id
-{
-	id_uptime = 0x01
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = LAYOUT(\
+    KC_INS,             KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_F1, \
+    KC_DEL,          KC_TAB,  KC_Q, KC_W, KC_E, KC_R, KC_T, KC_F2, \
+                  KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_F3, \
+             KC_LSFT,    KC_Z, KC_X, KC_C, KC_V, KC_B, KC_F4, \
+    KC_HOME, KC_END, KC_LCTL,    KC_LGUI, KC_LALT, KC_SPC, KC_F5 \
+  )
 };
--- a/keyboards/clueboard/unorthodox/mcuconf.h
+++ b/keyboards/clueboard/unorthodox/mcuconf.h
@@ -0,0 +1,257 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef MCUCONF_H
+#define MCUCONF_H
+
+/*
+ * STM32F3xx drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0       Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3        Lowest...Highest.
+ */
+
+#define STM32F3xx_MCUCONF
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT                       FALSE
+#define STM32_PVD_ENABLE                    FALSE
+#define STM32_PLS                           STM32_PLS_LEV0
+#define STM32_HSI_ENABLED                   TRUE
+#define STM32_LSI_ENABLED                   TRUE
+#define STM32_HSE_ENABLED                   TRUE
+#define STM32_LSE_ENABLED                   FALSE
+#define STM32_SW                            STM32_SW_PLL
+#define STM32_PLLSRC                        STM32_PLLSRC_HSE
+#define STM32_PREDIV_VALUE                  1
+#define STM32_PLLMUL_VALUE                  9
+#define STM32_HPRE                          STM32_HPRE_DIV1
+#define STM32_PPRE1                         STM32_PPRE1_DIV2
+#define STM32_PPRE2                         STM32_PPRE2_DIV2
+#define STM32_MCOSEL                        STM32_MCOSEL_NOCLOCK
+#define STM32_ADC12PRES                     STM32_ADC12PRES_DIV1
+#define STM32_ADC34PRES                     STM32_ADC34PRES_DIV1
+#define STM32_USART1SW                      STM32_USART1SW_PCLK
+#define STM32_USART2SW                      STM32_USART2SW_PCLK
+#define STM32_USART3SW                      STM32_USART3SW_PCLK
+#define STM32_UART4SW                       STM32_UART4SW_PCLK
+#define STM32_UART5SW                       STM32_UART5SW_PCLK
+#define STM32_I2C1SW                        STM32_I2C1SW_SYSCLK
+#define STM32_I2C2SW                        STM32_I2C2SW_SYSCLK
+#define STM32_TIM1SW                        STM32_TIM1SW_PCLK2
+#define STM32_TIM8SW                        STM32_TIM8SW_PCLK2
+#define STM32_RTCSEL                        STM32_RTCSEL_LSI
+#define STM32_USB_CLOCK_REQUIRED            TRUE
+#define STM32_USBPRE                        STM32_USBPRE_DIV1P5
+
+#undef STM32_HSE_BYPASS
+// #error "oh no"
+// #endif
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_DUAL_MODE                 FALSE
+#define STM32_ADC_COMPACT_SAMPLES           FALSE
+#define STM32_ADC_USE_ADC1                  FALSE
+#define STM32_ADC_USE_ADC2                  FALSE
+#define STM32_ADC_USE_ADC3                  FALSE
+#define STM32_ADC_USE_ADC4                  FALSE
+#define STM32_ADC_ADC1_DMA_STREAM           STM32_DMA_STREAM_ID(1, 1)
+#define STM32_ADC_ADC2_DMA_STREAM           STM32_DMA_STREAM_ID(2, 1)
+#define STM32_ADC_ADC3_DMA_STREAM           STM32_DMA_STREAM_ID(2, 5)
+#define STM32_ADC_ADC4_DMA_STREAM           STM32_DMA_STREAM_ID(2, 2)
+#define STM32_ADC_ADC1_DMA_PRIORITY         2
+#define STM32_ADC_ADC2_DMA_PRIORITY         2
+#define STM32_ADC_ADC3_DMA_PRIORITY         2
+#define STM32_ADC_ADC4_DMA_PRIORITY         2
+#define STM32_ADC_ADC12_IRQ_PRIORITY        5
+#define STM32_ADC_ADC3_IRQ_PRIORITY         5
+#define STM32_ADC_ADC4_IRQ_PRIORITY         5
+#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC12_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
+#define STM32_ADC_ADC34_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1                  FALSE
+#define STM32_CAN_CAN1_IRQ_PRIORITY         11
+
+/*
+ * DAC driver system settings.
+ */
+#define STM32_DAC_DUAL_MODE                 FALSE
+#define STM32_DAC_USE_DAC1_CH1              TRUE
+#define STM32_DAC_USE_DAC1_CH2              TRUE
+#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY     10
+#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY     10
+#define STM32_DAC_DAC1_CH1_DMA_PRIORITY     2
+#define STM32_DAC_DAC1_CH2_DMA_PRIORITY     2
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI1_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI2_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI3_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI4_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI5_9_IRQ_PRIORITY      6
+#define STM32_EXT_EXTI10_15_IRQ_PRIORITY    6
+#define STM32_EXT_EXTI16_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI17_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI18_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI19_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI20_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI30_32_IRQ_PRIORITY    6
+#define STM32_EXT_EXTI33_IRQ_PRIORITY       6
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1                  FALSE
+#define STM32_GPT_USE_TIM2                  FALSE
+#define STM32_GPT_USE_TIM3                  FALSE
+#define STM32_GPT_USE_TIM4                  FALSE
+#define STM32_GPT_USE_TIM6                  TRUE
+#define STM32_GPT_USE_TIM7                  TRUE
+#define STM32_GPT_USE_TIM8                  TRUE
+#define STM32_GPT_TIM1_IRQ_PRIORITY         7
+#define STM32_GPT_TIM2_IRQ_PRIORITY         7
+#define STM32_GPT_TIM3_IRQ_PRIORITY         7
+#define STM32_GPT_TIM4_IRQ_PRIORITY         7
+#define STM32_GPT_TIM6_IRQ_PRIORITY         7
+#define STM32_GPT_TIM7_IRQ_PRIORITY         7
+#define STM32_GPT_TIM8_IRQ_PRIORITY         7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1                  FALSE
+#define STM32_I2C_USE_I2C2                  FALSE
+#define STM32_I2C_BUSY_TIMEOUT              50
+#define STM32_I2C_I2C1_IRQ_PRIORITY         10
+#define STM32_I2C_I2C2_IRQ_PRIORITY         10
+#define STM32_I2C_USE_DMA                   TRUE
+#define STM32_I2C_I2C1_DMA_PRIORITY         1
+#define STM32_I2C_I2C2_DMA_PRIORITY         1
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp)      osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1                  FALSE
+#define STM32_ICU_USE_TIM2                  FALSE
+#define STM32_ICU_USE_TIM3                  FALSE
+#define STM32_ICU_USE_TIM4                  FALSE
+#define STM32_ICU_USE_TIM8                  FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY         7
+#define STM32_ICU_TIM2_IRQ_PRIORITY         7
+#define STM32_ICU_TIM3_IRQ_PRIORITY         7
+#define STM32_ICU_TIM4_IRQ_PRIORITY         7
+#define STM32_ICU_TIM8_IRQ_PRIORITY         7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED              FALSE
+#define STM32_PWM_USE_TIM1                  FALSE
+#define STM32_PWM_USE_TIM2                  TRUE
+#define STM32_PWM_USE_TIM3                  TRUE
+#define STM32_PWM_USE_TIM4                  FALSE
+#define STM32_PWM_USE_TIM8                  FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY         7
+#define STM32_PWM_TIM2_IRQ_PRIORITY         7
+#define STM32_PWM_TIM3_IRQ_PRIORITY         7
+#define STM32_PWM_TIM4_IRQ_PRIORITY         7
+#define STM32_PWM_TIM8_IRQ_PRIORITY         7
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1             FALSE
+#define STM32_SERIAL_USE_USART2             TRUE
+#define STM32_SERIAL_USE_USART3             FALSE
+#define STM32_SERIAL_USE_UART4              FALSE
+#define STM32_SERIAL_USE_UART5              FALSE
+#define STM32_SERIAL_USART1_PRIORITY        12
+#define STM32_SERIAL_USART2_PRIORITY        12
+#define STM32_SERIAL_USART3_PRIORITY        12
+#define STM32_SERIAL_UART4_PRIORITY         12
+#define STM32_SERIAL_UART5_PRIORITY         12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1                  FALSE
+#define STM32_SPI_USE_SPI2                  FALSE
+#define STM32_SPI_USE_SPI3                  FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY         1
+#define STM32_SPI_SPI2_DMA_PRIORITY         1
+#define STM32_SPI_SPI3_DMA_PRIORITY         1
+#define STM32_SPI_SPI1_IRQ_PRIORITY         10
+#define STM32_SPI_SPI2_IRQ_PRIORITY         10
+#define STM32_SPI_SPI3_IRQ_PRIORITY         10
+#define STM32_SPI_DMA_ERROR_HOOK(spip)      osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY               8
+#define STM32_ST_USE_TIMER                  2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1               FALSE
+#define STM32_UART_USE_USART2               FALSE
+#define STM32_UART_USE_USART3               FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY      12
+#define STM32_UART_USART2_IRQ_PRIORITY      12
+#define STM32_UART_USART3_IRQ_PRIORITY      12
+#define STM32_UART_USART1_DMA_PRIORITY      0
+#define STM32_UART_USART2_DMA_PRIORITY      0
+#define STM32_UART_USART3_DMA_PRIORITY      0
+#define STM32_UART_DMA_ERROR_HOOK(uartp)    osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1                  TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND      FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY      13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY      14
+
+/*
+ * WDG driver system settings.
+ */
+#define STM32_WDG_USE_IWDG                  FALSE
+
+#endif /* MCUCONF_H */
--- a/keyboards/clueboard/unorthodox/readme.md
+++ b/keyboards/clueboard/unorthodox/readme.md
@@ -0,0 +1,14 @@
+Unorthodox
+==========
+
+A split row-staggered keyboard with a symetric layout.
+
+Keyboard Maintainer: [Zach White](https://github.com/skullydazed)
+Hardware Supported: Unorthodox Kit w/Proton C
+Hardware Availability: TBD
+
+Make example for this keyboard (after setting up your build environment):
+
+    make clueboard/unorthodox:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
--- a/keyboards/clueboard/unorthodox/rules.mk
+++ b/keyboards/clueboard/unorthodox/rules.mk
@@ -0,0 +1,51 @@
+## chip/board settings
+# - the next two should match the directories in
+#   <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
+MCU_FAMILY = STM32
+MCU_SERIES = STM32F3xx
+
+# Linker script to use
+# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
+#   or <this_dir>/ld/
+MCU_LDSCRIPT = STM32F303xC
+
+# Startup code to use
+#  - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
+MCU_STARTUP = stm32f3xx
+
+# Board: it should exist either in <chibios>/os/hal/boards/
+#  or <this_dir>/boards
+BOARD = GENERIC_STM32_F303XC
+
+# Cortex version
+MCU  = cortex-m4
+
+# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
+ARMV = 7
+
+USE_FPU = yes
+
+# Vector table for application
+# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
+# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
+# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000
+OPT_DEFS =
+
+# Options to pass to dfu-util when flashing
+DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
+
+# Build Options
+#   comment out to disable the options.
+#
+BACKLIGHT_ENABLE = no
+BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration
+## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.)
+MOUSEKEY_ENABLE = yes # Mouse keys
+EXTRAKEY_ENABLE = yes # Audio control and System control
+CONSOLE_ENABLE = yes  # Console for debug
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes     # USB Nkey Rollover
+AUDIO_ENABLE = yes
+RGBLIGHT_ENABLE = no
+# SERIAL_LINK_ENABLE = yes
--- a/keyboards/clueboard/unorthodox/unorthodox.c
+++ b/keyboards/clueboard/unorthodox/unorthodox.c
@@ -0,0 +1,25 @@
+/* Copyright 2018 Jack Humbert
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "unorthodox.h"
+
+void matrix_init_kb(void) {
+  // Turn status LED on
+  //setPinOutput(C13);
+  //writePinHigh(C13);
+
+  matrix_init_user();
+}
--- a/keyboards/clueboard/unorthodox/unorthodox.h
+++ b/keyboards/clueboard/unorthodox/unorthodox.h
@@ -0,0 +1,32 @@
+/* Copyright 2018 Jack Humbert
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+#include "quantum.h"
+
+#define LAYOUT(\
+    k00,          k01, k02, k03, k04, k05, k06, k07, \
+    k10,        k11, k12, k13, k14, k15, k16, k17, \
+              k21, k22, k23, k24, k25, k26, k27, \
+         k31,    k32, k33, k34, k35, k36, k37, \
+    k40, k41, k42,    k43,   k44,    k46, k47 \
+) { \
+    { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+    { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+    { KC_NO, k21, k22, k23, k24, k25, k26, k27 }, \
+    { KC_NO, k31, k32, k33, k34, k35, k36, k37 }, \
+    { k40, k41, k42, k43, k44, KC_NO, k46, k47 }, \
+}
--- a/keyboards/converter/ibm_terminal/README.md
+++ b/keyboards/converter/ibm_terminal/README.md
@@ -1,40 +0,0 @@
-Keyboard converter for IBM terminal keyboard
-============================================
-
-This is a port of TMK's converter/terminal_usb to QMK.
-
-It supports PS/2 Scan Code Set 3 and runs on USB AVR chips such like PJRC Teensy.
-I tested the converter on ATMega32U4 with 1392595(102keys) and 6110345(122keys).
-
-Source code: https://github.com/qmk/qmk_firmware.git
-Article: http://geekhack.org/index.php?topic=27272.0
-
-
-CONNECTION
----------
-Keyboard    ATMega32U4
----------------------
-Data:       PD2
-Clock:      PD5
-
-And VCC and GND, of course. See RESOURCE for keyboard connector pin assign.
-
-
-BUILD
-----
-$ git clone https://github.com/qmk/qmk_firmware.git
-$ cd qmk_firmware
-$ make converter/ibm_terminal:default
-
-
-RESOURCE
--------
-Soarer's Converter: http://geekhack.org/index.php?topic=17458.0
-102keys(1392595): http://geekhack.org/index.php?topic=10737.0
-122keys(1390876): http://www.seasip.info/VintagePC/ibm_1390876.html
-KbdBabel: http://www.kbdbabel.org/
-RJ45 Connector: http://www.kbdbabel.org/conn/kbd_connector_ibmterm.png
-DIN Connector: http://www.kbdbabel.org/conn/kbd_connector_ibm3179_318x_319x.png
-WinAVR: http://winavr.sourceforge.net/
-
-EOF
--- a/keyboards/converter/ibm_terminal/ibm_terminal.h
+++ b/keyboards/converter/ibm_terminal/ibm_terminal.h
@@ -19,7 +19,7 @@ void matrix_init_user(void);
 * 17|         |
 *   +---------+
 */
-#define KEYMAP( \
+#define LAYOUT( \
                  K08,K10,K18,K20,K28,K30,K38,K40,K48,K50,K57,K5F,                                         \
                  K07,K0F,K17,K1F,K27,K2F,K37,K3F,K47,K4F,K56,K5E,                                         \
                                                                                                           \
@@ -45,13 +45,13 @@ void matrix_init_user(void);
    { K68,   K69,   K6A,   K6B,   K6C,   K6D,   K6E,   K6F   }, \
    { K70,   K71,   K72,   K73,   K74,   K75,   K76,   K77   }, \
    { K78,   K79,   K7A,   K7B,   K7C,   K7D,   K7E,   KC_NO }, \
-    { KC_NO, KC_NO, KC_NO, K83,   K84,   KC_NO, KC_NO, KC_NO,}, \
+    { KC_NO, KC_NO, KC_NO, K83,   K84,   KC_NO, KC_NO, KC_NO }  \
 }

 /*
 * IBM Terminal keyboard 1399625, 101-key
 */
-#define KEYMAP_101( \
+#define LAYOUT_101( \
    K08,    K07,K0F,K17,K1F,K27,K2F,K37,K3F,K47,K4F,K56,K5E,  K57,K5F,K62,                   \
                                                                                             \
    K0E,K16,K1E,K26,K25,K2E,K36,K3D,K3E,K46,K45,K4E,K55,K66,  K67,K6E,K6F,  K76,K77,K7E,K84, \
@@ -76,7 +76,7 @@ void matrix_init_user(void);
    { KC_NO, K69,   K6A,   K6B,   K6C,   K6D,   K6E,   K6F   }, \
    { K70,   K71,   K72,   K73,   K74,   K75,   K76,   K77   }, \
    { KC_NO, K79,   K7A,   KC_NO, K7C,   K7D,   K7E,   KC_NO }, \
-    { KC_NO, KC_NO, KC_NO, KC_NO, K84,   KC_NO, KC_NO, KC_NO,}, \
+    { KC_NO, KC_NO, KC_NO, KC_NO, K84,   KC_NO, KC_NO, KC_NO }  \
 }

-#endif
+#endif
--- a/keyboards/converter/ibm_terminal/info.json
+++ b/keyboards/converter/ibm_terminal/info.json
@@ -0,0 +1,245 @@
+{
+  "keyboard_name": "Keyboard converter for IBM terminal keyboard",
+  "url": "",
+  "maintainer": "qmk",
+  "width": 24.75,
+  "height": 8,
+  "layouts": {
+    "LAYOUT": {
+      "layout": [
+        {"label":"F13", "x":3.25, "y":0},
+        {"label":"F14", "x":4.25, "y":0},
+        {"label":"F15", "x":5.25, "y":0},
+        {"label":"F16", "x":6.25, "y":0},
+        {"label":"F17", "x":7.25, "y":0},
+        {"label":"F18", "x":8.25, "y":0},
+        {"label":"F19", "x":9.25, "y":0},
+        {"label":"F20", "x":10.25, "y":0},
+        {"label":"F21", "x":11.25, "y":0},
+        {"label":"F22", "x":12.25, "y":0},
+        {"label":"F23", "x":13.25, "y":0},
+        {"label":"F24", "x":14.25, "y":0},
+        {"label":"F1", "x":3.25, "y":1},
+        {"label":"F2", "x":4.25, "y":1},
+        {"label":"F3", "x":5.25, "y":1},
+        {"label":"F4", "x":6.25, "y":1},
+        {"label":"F5", "x":7.25, "y":1},
+        {"label":"F6", "x":8.25, "y":1},
+        {"label":"F7", "x":9.25, "y":1},
+        {"label":"F8", "x":10.25, "y":1},
+        {"label":"F9", "x":11.25, "y":1},
+        {"label":"F10", "x":12.25, "y":1},
+        {"label":"F11", "x":13.25, "y":1},
+        {"label":"F12", "x":14.25, "y":1},
+        {"label":"Print Screen", "x":0, "y":3},
+        {"label":"Esc", "x":1, "y":3},
+        {"label":"Esc", "x":2.25, "y":3},
+        {"label":"1", "x":3.25, "y":3},
+        {"label":"2", "x":4.25, "y":3},
+        {"label":"3", "x":5.25, "y":3},
+        {"label":"4", "x":6.25, "y":3},
+        {"label":"5", "x":7.25, "y":3},
+        {"label":"6", "x":8.25, "y":3},
+        {"label":"7", "x":9.25, "y":3},
+        {"label":"8", "x":10.25, "y":3},
+        {"label":"9", "x":11.25, "y":3},
+        {"label":"0", "x":12.25, "y":3},
+        {"label":"-", "x":13.25, "y":3},
+        {"label":"=", "x":14.25, "y":3},
+        {"label":"No", "x":15.25, "y":3},
+        {"label":"Back Space", "x":16.25, "y":3},
+        {"label":"Insert", "x":17.5, "y":3},
+        {"label":"Home", "x":18.5, "y":3},
+        {"label":"Page Up", "x":19.5, "y":3},
+        {"label":"Num Lock", "x":20.75, "y":3},
+        {"label":"/", "x":21.75, "y":3},
+        {"label":"*", "x":22.75, "y":3},
+        {"label":"-", "x":23.75, "y":3},
+        {"label":"Scroll Lock", "x":0, "y":4},
+        {"label":"Int4", "x":1, "y":4},
+        {"label":"Tab", "x":2.25, "y":4, "w":1.5},
+        {"label":"Q", "x":3.75, "y":4},
+        {"label":"W", "x":4.75, "y":4},
+        {"label":"E", "x":5.75, "y":4},
+        {"label":"R", "x":6.75, "y":4},
+        {"label":"T", "x":7.75, "y":4},
+        {"label":"Y", "x":8.75, "y":4},
+        {"label":"U", "x":9.75, "y":4},
+        {"label":"I", "x":10.75, "y":4},
+        {"label":"O", "x":11.75, "y":4},
+        {"label":"P", "x":12.75, "y":4},
+        {"label":"[", "x":13.75, "y":4},
+        {"label":"]", "x":14.75, "y":4},
+        {"label":"No", "x":15.75, "y":4, "w":1.5},
+        {"label":"Delete", "x":17.5, "y":4},
+        {"label":"End", "x":18.5, "y":4},
+        {"label":"Page Down", "x":19.5, "y":4},
+        {"label":"7", "x":20.75, "y":4},
+        {"label":"8", "x":21.75, "y":4},
+        {"label":"9", "x":22.75, "y":4},
+        {"label":"+", "x":23.75, "y":4},
+        {"label":"Pause", "x":0, "y":5},
+        {"label":"Int5", "x":1, "y":5},
+        {"label":"Caps Lock", "x":2.25, "y":5, "w":1.75},
+        {"label":"A", "x":4, "y":5},
+        {"label":"S", "x":5, "y":5},
+        {"label":"D", "x":6, "y":5},
+        {"label":"F", "x":7, "y":5},
+        {"label":"G", "x":8, "y":5},
+        {"label":"H", "x":9, "y":5},
+        {"label":"J", "x":10, "y":5},
+        {"label":"K", "x":11, "y":5},
+        {"label":"L", "x":12, "y":5},
+        {"label":";", "x":13, "y":5},
+        {"label":"'", "x":14, "y":5},
+        {"label":"\\", "x":15, "y":5},
+        {"label":"Enter", "x":16, "y":5, "w":1.25},
+        {"label":"Up", "x":18.5, "y":5},
+        {"label":"4", "x":20.75, "y":5},
+        {"label":"5", "x":21.75, "y":5},
+        {"label":"6", "x":22.75, "y":5},
+        {"label":",", "x":23.75, "y":5},
+        {"label":"App", "x":0, "y":6},
+        {"label":"Int6", "x":1, "y":6},
+        {"label":"Shift", "x":2.25, "y":6, "w":1.25},
+        {"label":"ISO \\", "x":3.5, "y":6},
+        {"label":"Z", "x":4.5, "y":6},
+        {"label":"X", "x":5.5, "y":6},
+        {"label":"C", "x":6.5, "y":6},
+        {"label":"V", "x":7.5, "y":6},
+        {"label":"B", "x":8.5, "y":6},
+        {"label":"N", "x":9.5, "y":6},
+        {"label":"M", "x":10.5, "y":6},
+        {"label":",", "x":11.5, "y":6},
+        {"label":".", "x":12.5, "y":6},
+        {"label":"/", "x":13.5, "y":6},
+        {"label":"No", "x":14.5, "y":6},
+        {"label":"Shift", "x":15.5, "y":6, "w":1.75},
+        {"label":"Left", "x":17.5, "y":6},
+        {"label":"Int2", "x":18.5, "y":6},
+        {"label":"Right", "x":19.5, "y":6},
+        {"label":"1", "x":20.75, "y":6},
+        {"label":"2", "x":21.75, "y":6},
+        {"label":"3", "x":22.75, "y":6},
+        {"label":"Enter", "x":23.75, "y":6},
+        {"label":"RGUI", "x":0, "y":7},
+        {"label":"lgui", "x":1, "y":7},
+        {"label":"Ctrl", "x":2.25, "y":7, "w":1.5},
+        {"label":"Alt", "x":4.75, "y":7, "w":1.5},
+        {"label":"Space", "x":6.25, "y":7, "w":7},
+        {"label":"Alt", "x":13.25, "y":7, "w":1.5},
+        {"label":"Ctrl", "x":15.75, "y":7, "w":1.5},
+        {"label":"Down", "x":18.5, "y":7},
+        {"label":"No", "x":20.75, "y":7},
+        {"label":"0", "x":21.75, "y":7},
+        {"label":".", "x":22.75, "y":7},
+        {"label":"No", "x":23.75, "y":7}
+      ]
+    },
+    "LAYOUT_101": {
+      "layout": [
+        {"label":"Esc", "x":0, "y":0},
+        {"label":"F1", "x":2, "y":0},
+        {"label":"F2", "x":3, "y":0},
+        {"label":"F3", "x":4, "y":0},
+        {"label":"F4", "x":5, "y":0},
+        {"label":"F5", "x":6.5, "y":0},
+        {"label":"F6", "x":7.5, "y":0},
+        {"label":"F7", "x":8.5, "y":0},
+        {"label":"F8", "x":9.5, "y":0},
+        {"label":"F9", "x":11, "y":0},
+        {"label":"F10", "x":12, "y":0},
+        {"label":"F11", "x":13, "y":0},
+        {"label":"F12", "x":14, "y":0},
+        {"label":"Print Screen", "x":15.25, "y":0},
+        {"label":"Scroll Lock", "x":16.25, "y":0},
+        {"label":"Pause", "x":17.25, "y":0},
+        {"label":"`", "x":0, "y":2},
+        {"label":"1", "x":1, "y":2},
+        {"label":"2", "x":2, "y":2},
+        {"label":"3", "x":3, "y":2},
+        {"label":"4", "x":4, "y":2},
+        {"label":"5", "x":5, "y":2},
+        {"label":"6", "x":6, "y":2},
+        {"label":"7", "x":7, "y":2},
+        {"label":"8", "x":8, "y":2},
+        {"label":"9", "x":9, "y":2},
+        {"label":"0", "x":10, "y":2},
+        {"label":"-", "x":11, "y":2},
+        {"label":"=", "x":12, "y":2},
+        {"label":"Back Space", "x":13, "y":2, "w":2},
+        {"label":"Insert", "x":15.25, "y":2},
+        {"label":"Home", "x":16.25, "y":2},
+        {"label":"Page Up", "x":17.25, "y":2},
+        {"label":"Num Lock", "x":18.5, "y":2},
+        {"label":"/", "x":19.5, "y":2},
+        {"label":"*", "x":20.5, "y":2},
+        {"label":"-", "x":21.5, "y":2},
+        {"label":"Tab", "x":0, "y":3, "w":1.5},
+        {"label":"Q", "x":1.5, "y":3},
+        {"label":"W", "x":2.5, "y":3},
+        {"label":"E", "x":3.5, "y":3},
+        {"label":"R", "x":4.5, "y":3},
+        {"label":"T", "x":5.5, "y":3},
+        {"label":"Y", "x":6.5, "y":3},
+        {"label":"U", "x":7.5, "y":3},
+        {"label":"I", "x":8.5, "y":3},
+        {"label":"O", "x":9.5, "y":3},
+        {"label":"P", "x":10.5, "y":3},
+        {"label":"[", "x":11.5, "y":3},
+        {"label":"]", "x":12.5, "y":3},
+        {"label":"\\", "x":13.5, "y":3, "w":1.5},
+        {"label":"Delete", "x":15.25, "y":3},
+        {"label":"End", "x":16.25, "y":3},
+        {"label":"Page Down", "x":17.25, "y":3},
+        {"label":"7", "x":18.5, "y":3},
+        {"label":"8", "x":19.5, "y":3},
+        {"label":"9", "x":20.5, "y":3},
+        {"label":"Caps Lock", "x":0, "y":4, "w":1.75},
+        {"label":"A", "x":1.75, "y":4},
+        {"label":"S", "x":2.75, "y":4},
+        {"label":"D", "x":3.75, "y":4},
+        {"label":"F", "x":4.75, "y":4},
+        {"label":"G", "x":5.75, "y":4},
+        {"label":"H", "x":6.75, "y":4},
+        {"label":"J", "x":7.75, "y":4},
+        {"label":"K", "x":8.75, "y":4},
+        {"label":"L", "x":9.75, "y":4},
+        {"label":";", "x":10.75, "y":4},
+        {"label":"'", "x":11.75, "y":4},
+        {"label":"Enter", "x":12.75, "y":4, "w":2.25},
+        {"label":"4", "x":18.5, "y":4},
+        {"label":"5", "x":19.5, "y":4},
+        {"label":"6", "x":20.5, "y":4},
+        {"label":"+", "x":21.5, "y":3, "h":2},
+        {"label":"Shift", "x":0, "y":5, "w":2.25},
+        {"label":"Z", "x":2.25, "y":5},
+        {"label":"X", "x":3.25, "y":5},
+        {"label":"C", "x":4.25, "y":5},
+        {"label":"V", "x":5.25, "y":5},
+        {"label":"B", "x":6.25, "y":5},
+        {"label":"N", "x":7.25, "y":5},
+        {"label":"M", "x":8.25, "y":5},
+        {"label":",", "x":9.25, "y":5},
+        {"label":".", "x":10.25, "y":5},
+        {"label":"/", "x":11.25, "y":5},
+        {"label":"Shift", "x":12.25, "y":5, "w":2.75},
+        {"label":"Up", "x":16.25, "y":5},
+        {"label":"1", "x":18.5, "y":5},
+        {"label":"2", "x":19.5, "y":5},
+        {"label":"3", "x":20.5, "y":5},
+        {"label":"Ctrl", "x":0, "y":6, "w":1.5},
+        {"label":"Alt", "x":2.5, "y":6, "w":1.5},
+        {"label":"Space", "x":4, "y":6, "w":7},
+        {"label":"Alt", "x":11, "y":6, "w":1.5},
+        {"label":"Ctrl", "x":13.5, "y":6, "w":1.5},
+        {"label":"Left", "x":15.25, "y":6},
+        {"label":"Down", "x":16.25, "y":6},
+        {"label":"Right", "x":17.25, "y":6},
+        {"label":"0", "x":18.5, "y":6, "w":2},
+        {"label":".", "x":20.5, "y":6},
+        {"label":"Enter", "x":21.5, "y":5, "h":2}
+      ]
+    }
+  }
+}
--- a/keyboards/converter/ibm_terminal/keymaps/default/config.h
+++ b/keyboards/converter/ibm_terminal/keymaps/default/config.h
@@ -1,6 +1,3 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once

-#include "../../config.h"
-
-#endif
+// place overrides here
--- a/keyboards/converter/ibm_terminal/keymaps/default/keymap.c
+++ b/keyboards/converter/ibm_terminal/keymaps/default/keymap.c
@@ -15,18 +15,12 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */

-#include <stdint.h>
-#include <stdbool.h>
-#include "keycode.h"
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "ibm_terminal.h"
+#include QMK_KEYBOARD_H

 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    // Layer 0

-    KEYMAP(
+    LAYOUT(
                        KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24,
                        KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,  KC_F10, KC_F11, KC_F12,

@@ -56,7 +50,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     * `----'    `---------------------------------------'    `----' `-----------' `---------------'
     */
 /*
-    KEYMAP_101(
+    LAYOUT_101(
     KC_ESC,       KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9, KC_F10, KC_F11, KC_F12,        KC_PSCR,KC_SLCK, KC_BRK,

     KC_GRV,   KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,KC_MINS, KC_EQL,KC_BSPC,      KC_INS,KC_HOME,KC_PGUP,     KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS,
--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
skullY	20e27feb7d	Initial unorthodox support	2018-11-14 08:46:58 -08:00
FiNeXdesign	e10a602e7b	Keymap: Finex Redox keymap (#4418 ) * Added FiNeX custom Redox Layout, first commit. * updated readme * removed old code	2018-11-13 14:44:50 -08:00
noroadsleft	991686203c	converter/m0110_usb Configurator support and readme cleanup (#4421 ) * Apple M0110 USB converter: readme cleanup * Apple M0110 USB converter: Configurator support	2018-11-13 14:20:42 -08:00
KOBAYASHI Daisuke	911b2d0756	Docs: Fix descriptions of KC_INT1 and KC_INT3	2018-11-13 12:27:33 -08:00
FateEverywhere	4609d68ddc	Keyboard: Add 412 64 Model 00 keyboard. (#4400 ) * Add 412-64 keyboard firmware It's pretty barebones for now, but the Model 00 is also a pretty barebones machine. Model 01 won't be better, but plenty of pins exist for things like LEDs on Model 02. * MANU/PROD ID changes. Changed around the MANUFACTURER and PRODUCT IDs to be more polite when viewed in qmk toolbox. * Fixing PROD again. For the love of all that is good and holy, that was ugly. This new one looks better. This stuff matters to me for some reason. * Yep, updating MANU again. There we go. That's better - From my name to my "design firm". * Update keyboards/412_64/keymaps/default/keymap.c Co-Authored-By: FateEverywhere <41215461+FateEverywhere@users.noreply.github.com> * Update keyboards/412_64/rules.mk Co-Authored-By: FateEverywhere <41215461+FateEverywhere@users.noreply.github.com> * Update keyboards/412_64/rules.mk Co-Authored-By: FateEverywhere <41215461+FateEverywhere@users.noreply.github.com> * Update keyboards/412_64/rules.mk Co-Authored-By: FateEverywhere <41215461+FateEverywhere@users.noreply.github.com> * Update keyboards/412_64/rules.mk Co-Authored-By: FateEverywhere <41215461+FateEverywhere@users.noreply.github.com>	2018-11-13 08:38:48 -08:00
Wilba	2dea540afb	Refactoring M6-A, M6-B, Zeal60, Zeal65, WT60-A, WT65-A, WT80-A (#4417 ) * Refactored M6-B to use Zeal60 RGB backlight code * Fixed M6-B LED co-ordinates * Minor changes to RGB config for Zeal65 * Added dynamic keymaps to WT80-A, WT60-A, WT-80A, U80-A	2018-11-13 08:31:25 -08:00
Junya Ogura	caa293a8f7	Remove duplicate row from Available functions table in i2c_driver doc (#4416 )	2018-11-13 08:27:46 -08:00
noroadsleft	7e87532ec2	converter/ibm_terminal Refactor and Configurator support (#4414 ) * IBM Terminal converter: layout macro refactor - Renamed KEYMAP to LAYOUT - Renamed KEYMAP_101 to LAYOUT_101 - minor matrix array fixes * IBM Terminal converter: default keymap refactor - Updated layout macro names - Updated to #include QMK_KEYBOARD_H - config.h updated to use #pragma once * IBM Terminal converter: priyadi keymap refactor - Updated layout macro names - Updated to #include QMK_KEYBOARD_H - Removed redundant KC_TRNS and KC_NO defines - config.h updated to use #pragma once * IBM Terminal converter: Configurator support * IBM Terminal converter: readme cleanup Updated markdown formatting. * IBM Terminal converter: readme rename Renamed file to fully lowercase.	2018-11-13 08:26:55 -08:00
Andrew Kannan	709bf386f4	Update Practice60 to use MT feature and revise system ticks (#4413 ) * Update Practice60 to use MT feature and revise system tics * Increase system tick frequency 10,000 instead of 10,000	2018-11-12 22:03:48 -08:00
MechMerlin	9b28dc8488	KBDFans KBD67 Support (#4412 ) * initial commit for kbd67 keyboard * add in a standard matrix * get the correct matrix for layout_all * add a layout_65_ansi LAYOUT macro * get a default keymap in * add caps lock led support * fix formatting of my name in the comments * add QMK Configurator support * turn on bootmagic	2018-11-12 21:46:34 -08:00
TheOneTrueTrench	2dc14d1cb3	Fixed incorrect link to feature_combo.md in features.md docs file. Was linked to feature_combos.md, but _sidebar.md, _summary.md, and config_options.md all link to feature_combo.md. Assuming that it should not be pluralized. (#4411 )	2018-11-12 16:46:01 -08:00
Andrew Kannan	e653cc198e	The "Practice60" Board, Blue Pill powered (#4407 ) * Starting point for blue pill based practice60 * Changes * add * try raw bin no botloader * swap back to bootloader version * edit * Remove debug LED flash * Disable JTAG to open up B3 and B4 * Add led backlight support (no breathing yet) * Update matrix for correctness * RGB Underglow working in a very simple state * not as bright * Move to handwired * revert ChibiOS_Test changes * Changes based on PR comments * Address PR comments v2 * Move files	2018-11-12 16:31:22 -08:00
				`@@ -0,0 +1 @@`
				`KEY_LOCK_ENABLE = yes # Enable the universal locking key, which lets you do any locking you require.`